- Masking tape
- Plastic scraper
- Kitchen wall sticker
Before starting to apply the adhesive on the wall, make sure the wall is well prepared, dry and free of any kind of dirt.
Quick Tip: on walls with floor, passing a cloth with alcohol helps to remove all dirt and leave the surface ready.
If the location where you will apply has taken, switches or records of water remove the mirrors of them with the help of a tool specifies. That way it will be easier to apply, and in the end will be better done.
With a piece of masking tape on hand, roll out (extend) the adhesive positioning on the wall the way you want it to be applied, with the liner (white paper) facing the wall, then attach the sticker on top with help of a piece of masking tape.
Note: If you purchased a large sticker that came into separate parts, similarly, position and attach (with masking tape) on the wall all parts so that you will have the basis of how the wall and will not risk missing space or something. Read here for more.
Important tip: Usually the wall stickers with more complex figures come with two protective films, one is the liner (white paper) and the other is the mask (front paper more transparent), do not remove the protections, they will be dropped at the right time, during application (step 3:00 pm on …).
Move away from the wall where it is attached the patch and see if it is positioned the way you want to.
If you need to make adjustments so that it is in the desired position.
After given the position, with the adhesive wall, go apart from the liner (white paper) from top to bottom, and as for taking (the liner), go scraping the sticker against the wall with the plastic spatula.
Pass the spatula always from the top down and from the Center to the edges, so will the patch create bubbles or wrinkles.
Do this process until the end.
If the adhesive is separated into parts, begin applying the larger piece.
Extra Tip: If the patch is large, with he set (with masking tape), roll again, and as applying, go rolling out. If necessary, ask for help from someone.
Quick Tip: If you create a few small bubbles at the time of application, don’t worry, continue the application and after you’re done, stick the bubbles with the help of a fine needle and press the bubble against the wall for her to disappear.
Important tip: If you are applying in a location that has contact with water, for example, near the sink, apply with calm to avoid bubbles and wrinkles, because holes in the adhesive can facilitate the penetration of water beneath.
After you have set the adhesive completely on the wall, take off that mask (more transparent), so that way you stay in the wall only the adhesive.
To remove the mask, always try to pull her flush to the wall, from top to bottom, so will avoid to leave the patch together.
If the adhesive skirt along with the mascara, mascara and some “scraped” with the finger or spatula on the part where the adhesive is leaving stuck to the adhesive stay on the wall and leave just the mask.
Step 5 (optional):
If you have purchased a large sticker that came into separate parts, after having applied the larger piece of adhesive, start applying the other.
When applying the adhesive,-if you have removed the mirrors-make a small cut on the sticker in the area where the outlet, switch or water logging, and place the mirrors back.
Once applied, wipe dry and clean around the sticker to take hand and end marks.
If the adhesive that you chose is simpler, as for example, the wall stickers which imitate tiles, the application process is virtually the same, however, even simpler, because this type of adhesive usually comes only with the liner.
Extra Hint (optional): to apply more easily simple figures stickers on walls with hardwood floors, moisten the wall with a moist cloth with water and mild detergent as mentioned by this page, so it’s easier for you to apply, and if you put wrong or stay with bubble, will be easier to get, because the adhesive will not fix at the same time, because of the moisture.
Remember to pass the spatula on the sticker to get all the excess moisture (water) you have underneath the sticker.
After 3 to 5 hours it will dry and be well fixed.
Other tips about applying for kitchen wall sticker
1-after applied, avoid doing in the kitchen, for at least 3 days, things that emit a lot of steam because the adhesive can end up releasing.
2-If you have little time or are afraid to apply on your own, hire a professional to do the implementation.
If you are purchasing in any physical store in your town, be aware that most of the time, the store itself offers a professional to do the implementation. Ask the attendant (before you buy) if the store offers the service.
Now, if you are purchasing online, try (before) in the phone book or the internet, shops of decoration or adhesives companies in your city, and check if the store or company offers a professional to make the application of the adhesive.
The workmanship is usually cheap and the result is very good.
Decor: Cute Chef Skinny Cook Kitchen Decals For Kitchen …
Wall Decorating Ideas and Tips for the Stunning yet Unique …
High gloss cabinet design, reproduction kitchen decals …
Interior Design Ideas For Kitchen – A Welcoming Kitchen …
Kitchen Wall Stickers Decoration Idea – Modern
Original Wall Stickers for Kitchen Design
Creative cartoon kitchen door stickers fridge stickers …
DIY Bathroom Wall Decor You’ll Fall in Love with …
Wall Decal: Kitchen Decals For Walls Ideas You Can Apply …
Wonderful ways to decorate your kitchen with kitchen wall …
2 Coffee Cups Kitchen Wall Stickers Cafe Vinyl Art Decals …
Kitchen Wall Decor ideas
Kitchen Wall Quote Vinyl Decal Lettering Decor Sticky
Retro Kitchen Wall Sticker by Vinylize Wall Deco …
Peachy Kitchen Wall Decor Home Design Ideas Photo For …
Decorate your kitchen with cool vinyl wall decals …
Wall Stickers For Kitchen Design
Kitchen : Stunning Kitchen Wall Decor Ideas With White …
36 Best Kitchen Wall Decor Ideas and Designs for 2018
Kitchen Came With House, Funny Kitchen Wall Sticker Quote